中村 俊哉

The interfacial stress between fibers and matrix plays an important role in the durability and damage initiation of carbon fiber reinforced composites. In this study, thermoelastic analysis was performed on a plate containing randomly distributed multiple fibers. Complex stress functions were employed with a semi-numerical method to ensure displacement continuity along the fiber/matrix interface as a boundary condition. The statistical investigation reveals that the stress concentration due to the presence of multiple fibers increases as the fiber density increases, though its deviation decreases. A numerical case study was conducted to discuss the micromechanics of the inherent scatter of material strength. The stress-strength model with Monte-Carlo simulation demonstrated the fracture probability calculation. The uncertainty obtained is partially attributed to the micromechanical stress variation around the fibers.

The objective of this study is to develop a novel aircraft design approach using biomimetics as an alternative to traditional airframes. This approach is primarily inspired by the dragonfly wing, which possesses reinforcement structures composed of cross veins and longitudinal veins. These structures are assumed to regulate deformation and enhance stiffness, respectively. The cross veins were replicated using weighted centroidal Voronoi tessellation (WCVT) based on the out-of-plane displacement of the skin. In contrast, the longitudinal veins were replicated by extracting a centerline from the topology optimization (TO) results on the skin, achieved through image analysis techniques such as binarization and skeletonization. The longitudinal layout effectively reduces compliance by distributing internal loads, utilizing only essential reinforcements on the skin without increasing its mass. The WCVT layout significantly enhances the buckling resistance of the reinforced skin. As a result, the skin reinforced using both cross–longitudinal layouts from TO and WCVT exhibited a buckling load 2.7 times greater while maintaining a lower mass compared to conventional layouts.

An analytical approach was developed for assessing the thermal history of thermoplastic composites during tape placement for in-situ consolidation of the automated fiber placement (AFP) technique. In this study, the heat-conduction equation is developed and solved for internal energy instead of temperature because the diffusivity does not significantly change over a wide range of temperatures in the AFP process, despite the significant change in the specific heat and conductivity. The three-dimensional internal energy history is derived in an integrated form using the Green function technique. The temperature field obtained from the internal energy field agreed with the finite element solution, where the temperature-dependent thermal properties were considered. The effects of manufacturing parameters, such as the placement speed and thickness of the placed laminates, on the thermal history of laminated composites during AFP are discussed using the present approach and finite element analysiss.

Tensile tests of quasi-isotropic laminates with a circular open hole, which include a gap in the hole area, were conducted to demonstrate the effect of the gap on the strength. The test showed that the reduction in the open-hole strength owing to the gap was less significant than that in the no-hole tensile strength. A two-dimensional mechanical model of quasi-isotropic laminates with an arbitrary inclined gap was proposed and analytically solved to obtain a closed-form expression for the stress concentration. An approximate expression was provided as the sum of the global uniform stress field and the local stress field near the open hole, which was solved based on a complex variable method. The present analytical solution agrees well with the corresponding two-dimensional finite element solutions. The solution indicated that the stress increase owing to the gap is limited at the stress concentration area. The analytical results were consistent with the experimental results.

Compression tests of quasi-isotropic laminates with embedded gaps were conducted to reveal the effect of the gap(s) on their compressive strength. Specimens were prepared such that the gaps are located at designated relative positions on a free side edge of the gage section. An analytical solution for a two-dimensional mechanical model of quasi-isotropic laminates with an arbitrary inclined gap is used to estimate the stress changes at the free edge owing to inclined gaps in the arbitrary relative locations. The relative reductions in the compressive strengths of the specimens with different gap arrangements were consistent with the analytically estimated increases in stress. The present results indicate that the significant reduction in compressive strength is caused not only by the waviness of the laminas at the gaps but also by the stress concentration at the free boundary due to the gap ends. Moreover, it is found that the standardized compression test may not be adequate to investigate the effect of the defect introduced by automated-fiber-placement method on the strength of the laminates because the sizes of the gage section of the compression test specimens specified by standard test methods are small compared to the gap spacing.